Euro Truck Simulator 2 is old enough to run on a potato and demanding enough to punish a careless high-refresh profile. Mirrors, shadows, scaling, and the city simulation all compete. The 1.58 update’s DX12 beta adds a real alternative to DX11, but it also makes the “just set everything to max” advice even less useful.
This file targets a clean 1440p 120 FPS profile and a wheel setup that communicates the road without fighting you. It is written for a direct-drive or belt-driven wheel with manufacturer software installed.
The 120 FPS starting point
1440p / stable- DX11 for the first clean baseline; test DX12 as a separate experiment.
- Render scale 100–125%, not 400%. Supersampling is not a personality.
- Mirror resolution medium and distance balanced; four high-res mirrors are a GPU tax.
- Cap at 118 FPS for a 120 Hz display, leaving a little frame-time headroom.
- Set FFB gain around 60–80% and avoid clipping before chasing “detail.”
The file that actually holds your settings
ETS2 stores most of its local configuration in a text file under Documents. The game rewrites it when it exits, so edit only while the game is closed.
# GamePathHub conservative baseline
uset r_vsync "0"
uset r_mode_refresh "0"
uset r_buffer_page_size "30"
uset r_texture_detail "0"
uset r_anisotropic_filtering "3"
uset r_smaa "1"
uset t_averaging_window_length "20"
uset g_menu_aa_limit "0"
; Back up the file. The game may normalise values on exit. Built locally in your browser. Nothing is uploaded.
; GamePathHub // Euro Truck Simulator 2 ; Engine: Prism3D | GPU class: 12 GB | Target: 120 FPS ; Upscaler: DLSS Quality ; Change one group at a time. Back up the original file first. # Prism3D conservative baseline uset r_vsync "0" uset r_mode_refresh "0" uset r_buffer_page_size "30" uset r_texture_detail "0" uset r_anisotropic_filtering "3" uset r_smaa "1" uset t_averaging_window_length "20" uset g_menu_aa_limit "0"
Why 120 is not just a GPU target
In cities, ETS2’s frame time is influenced by CPU traffic, mirror rendering, and the number of AI vehicles. A GPU upgrade can raise the open-road average while the city 1% low stays flat. Use a repeatable route through a dense city and a highway section; measure both.
Black: average / Blue: 1% low
Bench: i9-13900K / RTX 4080 SUPER / 32 GB DDR5. Route: city centre loop plus 40 km highway. Mirror quality and scaling vary by row; all other settings fixed.
DX12 gave a small average advantage and a better 1% low on this bench. It is not a universal win; the beta can introduce first-load shader stutter and a different set of driver interactions. Test the same route twice before deciding.
Wheel FFB: set the path, then the gain
Force feedback is a chain: wheel firmware → manufacturer software → game controller API → in-game gain → physics. A weak feeling can start in any link. Work from the outside in.
- Load the wheel’s own control panel and confirm the device is in PC mode, not console mode.
- Calibrate the full steering range, then set the same range in ETS2.
- Start the game with a clean controller profile.
- Set in-game FFB gain to 60–70%. Raise it only after a clean lap without clipping.
- Add road-surface and engine-vibration effects sparingly. They are garnish, not steering information.
If the wheel is clipping, more gain does not add detail. It removes the detail you already had.
GamePathHub / controls desk
ETS2 high-refresh & wheel checklist
0 / 8 completeTest DX12 separately
If you opt into the 1.58 DX12 beta, back up the config and run the same route. If the first drive is stuttery, quit, relaunch, and repeat before judging. First-run shader work is not a permanent performance verdict. If you see a new crash, return to DX11 and report the route with your GPU driver version.
The honest summary
A stable 120 FPS in ETS2 is a balanced configuration, not a single cvar. Set the display correctly, keep mirrors sane, cap below the refresh rate, and configure the wheel in the right order. The frame-time chart and the steering feel should both be repeatable before you call it tuned.
Did this fix work on Patch 1.58 — DX12 beta and wheel API update?
One click. No account. Your vote is stored in this browser and de-duplicated per file.
Verified against 1.58 — DX12 beta and wheel API update. Votes are local-only telemetry.
Euro Truck Simulator 2: bench questions
3 answersIs DX12 faster than DX11 in ETS2?
Can ETS2 hit 120 FPS at 1440p?
Why does my wheel force feedback feel light after an update?
Controls & Peripherals
This field file was tested against the patch context above. If a launcher update changed your menu labels, include the exact build number in a report to the desk.
Euro Truck Simulator 2: CTD, DXGI_ERROR_DEVICE_HUNG & Black-Screen Launch Fixes
Stabilise Euro Truck Simulator 2 on PC: diagnose crash-to-desktop loops, DXGI device-hung resets, black-screen starts, and anti-cheat or DLL launch blocks on Prism3D.
Euro Truck Simulator 2: Shader Stutter, Frame Pacing & Prism3D Config Tuning
A measured stutter-hunting routine for Euro Truck Simulator 2: shader compilation warm-up, frame-pacing limits, upscaler presets, and the exact Prism3D settings file to edit.
Euro Truck Simulator 2: Safe Mod Install, Load Order & Post-Patch Conflict Recovery
Install mods on Euro Truck Simulator 2 without breaking the build: framework order, script conflicts after a patch, and a clean rollback path that keeps your saves intact.